四网合一光缆交接箱(容量:144芯288芯、432芯、576芯、720芯、840芯、960芯、1152芯、1200芯、1440芯)公司主营产品:光缆交接箱,光纤分线箱,光分路器箱,光纤楼道箱,光分路箱,光分路器配线箱,光纤跳线尾纤,光纤快速连接器,光纤耦合器,光纤面板,光缆接头盒,光纤盒,光纤配线箱,光分路器,光纤冷接子,ODF单元箱,阴阳衰减器,光纤热缩管,祼纤保护管,熔纤盘,法兰支架,三叶线环,储纤筒,过线环,绕线环,光缆固定,多媒体信息箱等
1. Characteristics of traditional optical fiber transfer boxes
High strength SMC box structure, weatherability and strong corrosion resistance.
The box door is locked at three points, the door hinge is built, it is effective against theft and destruction.
Tray type termination unit, modular design, convenient for system expansion and installation.
Reliable optical fiber cable introduction and fixed protection device is suitable for non ribbon optical cable and ribbon optical cable.
It is suitable for installation of FC, SC, LC, ST and other adapters.
The full radius of curvature is greater than 37.5mm.
Two, outdoor optical cable transfer box product description
GXF05 series optical cable junction box is an interface device used at the junction of main optical cable and distribution optical cable in optical transmission network. It is used to realize the fixed and protection of optical cable, the fusion end of optical cable, the protection of optical fiber junction point, the distribution and dispatch of optical fiber line, the protection of internal equipment and the installation of other value-added
FTTH共建共享室光缆交接箱|欣昊四合一光缆交接箱(中国电信||广电网络|移动通信,FTTH四合一光缆交接箱是用于光纤接入网三网主干光缆与FTTH小区配线光缆节点处的接口设备,可以实现大容量光纤的熔接,终端存储以及调度等功能。该产品的应用,减少了三网的重复线路建设,精简线路,美化环境。*共和国通信行业标准通信光缆交接箱 Cross Connecting Cabinet for Communication Optical Cable YD/T 988-1998 1 范围 本标准规定了通信光缆交接箱。光缆交接箱用于光纤接入网中主干光缆与配线光缆交接处的接口配线设备。可对主,配线光缆进行固定,开剥,保护,终接及冗纤的盘绕,通过光纤跳线,能迅速方便地调度光缆中光纤序号以及改变传输系统的路由。产品具备模块化设计,优化的光缆管理系统,实现主干光缆与配线光缆交叉连接或互连,以及主干光缆之间的直通连接配线功能。且适用于多元化的XPON建设需求,提供多种光分路器增值单元解决方案
FTTH co-construction shared room optical cable junction box | Xinhao four-in-one optical cable junction box (China Telecom | China Unicom | Radio and Television Network | mobile communication special purpose, FTTH four-in-one optical cable junction box is used for optical access network three backbone cable and FTTH district distribution cable node interface equipment, can achieve large capacity optical fiber fusion, terminal storage to And dispatching functions. The application of this product reduced the construction of repeated lines in three networks, streamlined the lines and beautify the environment. Cross Connecting Cabinet for Communication Optical Cable YD/T 988-1998 1, the standard of communication industry of the People's Republic of China, stipulates the communication optical cable handover box. The optical cable transfer box is used for the interface wiring equipment between the main optical fiber cable and the wiring optical fiber cable in the optical fiber access network. It can fix, peel, protect, terminate and coil redundant fibers for main and distribution cables. It can quickly and conveniently dispatch the serial number of fibers and change the routing of transmission system through fiber jumper. The product has modular design, optimized cable management system, cross connection or interconnection between backbone cable and distribution cable, and direct connection and distribution function between backbone cable. It also applies to diversified XPON construction needs, and provides various optical splitter value-added unit solutions.
【功能要求】
1.光缆固定与保护功能:应具有光缆接入,固定和保护装置。该装置将光缆引入并固定在机架上,保护光缆入缆中纤芯不受损伤。光缆金属部分与机器绝缘,固定后的光缆金属护套及加强芯应可靠连接高压防护接地装置。
2.光缆终接功能:应具有光纤终接装置,该装置便于光缆纤芯及尾纤接续操作、施工、安装和维护。能固定和保护接头部位平直而不位移,避免外力影响,保证盘绕光缆纤芯、尾纤不受损伤。
3.调线功能:通过光纤跳线连接器接头。能迅速方便地调度光缆中的纤芯序号及改变光传输系统的路序。
4.光缆纤芯和尾纤的保护功能:光缆开剥后纤芯有保护装置并固定后引入光纤终接装置。
5.容量:每机架容量和单元容量(按适配器数量确定)应在产品企业标准中作出规定,光纤终接装置,尾纤盘线装置,适配器卡座,尾纤及适配器,在满容量范围内应能成套配置。
【安装说明】
1.落地安装时:先在预制的水泥基座上按安装尺寸预留4个M12的地脚螺钉,地脚螺钉凸出基座表面约为150mm,安装时先打开设备门,将设备内底部的两个插销拔出,并打开设备底座面板,将设备放在水泥基座上,用螺母将底座内的地脚螺钉拧紧,合上基座面板,插好插销,锁紧面板。
2.架空安装时:在站台适当位置留出4个φ13孔,根据安装尺寸将设备固定可靠
主要特点
1.箱体采用高强度的国际材料SMC(玻璃纤维增强不饱和聚酯塑料)经高温模压而成,使用寿命长,防老化、抗辐射;表面不需任何防护,具备全天候防护功能。
2.箱体厚实,具有良好的隔热效果,能有效防止箱内水汽凝结
3.箱门采用特种密封门封、防水门锁及三点式门销锁定,安全可靠,密封性好。
4.采用12芯熔接配线一体化模块。
5.适合FC、SC、LC、ST光纤适配器的安装。
6.有可靠的光缆固定和接地保护装置。
7.适合于单芯和带状光缆的成端。
8.有效做到移动、联通、电信三网合一。大大节省了施工空间和施工强度。
9.箱体防护等级达到GB/T4208-1993标准中IP65等级要求。
10.美观大方,线条清晰,防腐防水性能好,使用寿命长。
11.光缆交接箱规格:48芯、72芯、96芯、144芯、288芯、360芯、432芯、576芯、648芯、720芯、864芯、1152芯。
.功能要求:
1. 光缆固定与保护功能
应具有光缆接入,固定和保护装置。该装置将光缆引入并固定在机架上,保护光缆入缆中纤芯不受损伤。光缆金属部分与机器绝缘,固定后的光缆金属护套及加强芯应可靠连接高压防护接地装置。
2. 光缆终接功能
应具有光纤终接装置,该装置便于光缆纤芯及尾纤接续操作、施工、安装和维护。能固定和保护接头部位平直而不位移,避免外力影响,保证盘绕光缆纤芯、尾纤不受损伤。
3.调线功能
通过光纤跳线连接器接头。能迅速方便地调度光缆中的纤芯序号及改变光传输系统的路序。
4.光缆纤芯和尾纤的保护功能
光缆开剥后纤芯有保护装置并固定后引入光纤终接装置。
5.容量
每机架容量和单元容量(按适配器数量确定)应在产品企业标准中作出规定,光纤终接装置,尾纤盘线装置,适配器卡座,尾纤及适配器,在满容量范围内应能成套配置。